Notice: Undefined offset: 1 in /home/jackycho/public_html/hungtatester.com/wp-content/themes/replete/framework/php/function-set-avia-frontend.php on line 1015

Purpose: Use this tester to perform material verification tests of vehicle’s lamps, and mechanical property degradation tests of hand-carried communication devices, vehicle’s chassis parts and
bike’s parts.
Dimension of test trough:800 x 1400 x1400 mm ( W x D x H )
Area occupied by hanging board of test specimens:100 x 1000 mm ( D x H )
Performance:Room temperature 25 ℃ ± 5 ℃ and empty load on machine unit.

Model HT-2530
Spray test method The spray gun used shall be equipped with a nozzle 1.3 mm in diameter allowing a liquid flow rate of 0.24 ± 0.02 liter / minute at an operating pressure of 6.0 bars ~ 6.5 bars. The jet shall be sprayed the mud & water almost perpendicular to the surface to be tested at a distance of 380 mm ± 10mm from the samples and the area impacted on the surface shall be 170 ± 50 mm
Test mixture ( mud and sands):
Contents of test
mixture are as follows
Sands for test ( *PS:supplied by custome r)- silica sands at a hardness of 7 in Mohs scale, a grain size in between 0 and 0.2mm in normal distribution and an angular coefficient ranging from 1.8 to 2.0.

The hardness shall not exceed 205 g / m3 when 25 g of sand contained in a liter of mixture.

Structure and material of machine unit Materials for interior parts-stainless steel plate ( SUS#316 )
Materials for exterior parts-iron plate with powder coating
Materials for thermal insulation-PU foam cotton used for thermal insulation
Mud & water boost pump-high-pressure metering water pump
Material-Plastic steel material resistant to corrosion and wear.
Max. working pressure - 8 kg / cm 2, ( commonly used pressure: 6 kg / cm2 )
Max. flow rate-0.3 L / min, (commonly used flow rate:0.24 L / min )10 stages adjustable.
Flow meter-Flow meter of high pressure type
Material-Plastic steel material resistant to corrosion and wear.
Max. working pressure - 8 kg / cm2, ( commonly used pressure: 6 kg / cm2 )
Max. flow rate-0.3 L / min, ( commonly used flow rate:0.24 L / min )
Nozzle-Nozzle of high pressure type
Material-Tungsten steel resistant to corrosion and wear.

Jet diameter-1.3 mm F, conically shaped spray structure, able to spray an area in a diameter of 1705 mm at 380 mm distant to the nozzle.

Water reservoir-Made of stainless steel plate, able to receive a water volume about 100 liters at a proportioning rate of 25 g / liter of mud and sand, accessorized with mixing device ( to be
operated before spraying ) and recovery device of mud & sand ( to be operated after spraying).
Water pump for cleaning-made of stainless steel, can be applied to clean the spraying gun and test trough individually in two water circuits after the completion of spraying test.
3 – dimensional conveying rails for spray gun-made of stainless steel, can be run along X, Y, Z axes respectively.
Z axis (move forward and backward):Travel 600 mm, minimum designated unit:1mm, single acting movement for alignment.
X axis (move leftward and rightward):Travel 1000 mm, minimum designated unit 1mm, moving speed (50 ~ 500 mm/sec)
Y axis (move upward and downward):Travel 1000 mm, minimum designated unit 1mm, moving speed (50 ~ 500 mm/sec)
Hanging rack for test sample Made of stainless steel, maximum load 50 kg.
Test trough plate single-door model, accessorized with sight glass window and lamp for illumination.
Power supply:AC 3F 220V 60/50 Hz 50A AC 3F 380V 60/50 Hz 40A
© Copyright - Hungtatester